Guide · Office managers · 3 min read · Updated 16 November 2026
Office Copier and Printer Removal: Preparation Checklist
Short answer
Before copiers and printers are collected, list every machine with its model and serial number, deal with the internal storage, remove toner and paper, and check the route from each machine to the vehicle, including lift size and stair widths. Book any loading bay or lift with building management, tell reception, and make sure someone can sign the waste transfer note on the day.
One to two weeks before
Good preparation is the difference between a forty-minute collection and a half-day of waiting for lifts and keys. Start by walking the office and writing down every device going, including the forgotten printer in the post room and the plotter in the drawing office. Note which machines are leased, because those may need to go back to the supplier rather than for recycling. This is also the moment to tell staff what is happening. Let teams know which printers will disappear and when, and set up replacement print routes in advance so nobody is caught out on the morning of the collection.
- List each machine with make, model, serial number and location
- Confirm ownership of each copier, especially leased units
- Decide how storage will be handled and whether you need destruction records
- Book the goods lift, loading bay or parking with building management
- Ask whether out-of-hours removal is required by the building or lease
Measuring the route
Floor-standing copiers are big. A typical A3 machine with its cabinet is around 60 to 70 cm wide and deep and over a metre tall, and the finisher adds more width. Measure every door the machine must pass through, the lift door and car interior, and any tight turns on stairs. Tell us about thresholds, steps up to the entrance and any fire doors that must be held open. Most machines tilt slightly or can lose their finisher and trays to get through narrower gaps. What we need to know is whether there is any point where a stair climber cannot be used or the lift is too small, because that changes the crew and kit we send.
| Check | Why it matters |
|---|---|
| Door widths on the route | Decides whether finishers and trays must come off first |
| Lift door size and weight limit | Heavy copiers can exceed small passenger lifts |
| Stair width and turns | Stair climbers need room to pivot on landings |
| Floor finish | Polished or soft floors may need protection boards |
| Vehicle access and parking | Long carries to the van add time |
Preparing the machines
Run the data overwrite function on each copier while it still works, and delete address books and stored jobs. Remove paper from every tray, take out loose staples and empty the hole-punch waste box, which spills easily. Leave toner cartridges in place if you want them taken with the machine, or bag spare cartridges separately so they can go for remanufacture. Unplug machines and disconnect network cables the day before if you can, and clear the floor around each one. Copiers often sit in alcoves with shelving or bins crammed around them, which slows the crew down.
Label each machine with a simple tag showing whether it is going for recycling, back to a supplier or staying. In busy offices, especially during a move, it is surprisingly easy for the wrong copier to be loaded. A clear label on the front panel removes the guesswork for the crew and saves an awkward return trip. Coloured tags or simple printed labels both work well.
On collection day
Have one named contact on site who knows the building, has any keys or access passes, and can answer questions about which machines are going. Let reception and security know the crew are coming. The operatives will check each machine against the list, remove finishers and decks where needed, protect corners and floors, and move the equipment out using trolleys, skates or a stair climber. Before the crew leave, check that the waste transfer note lists the equipment correctly and that any drive destruction records will follow with serial numbers. Keep both together for at least two years. If anything changes on the day, such as an extra machine being added or one being kept back, tell the crew lead before loading starts so the paperwork matches what actually leaves. It is far easier to correct a note on site than to chase an amended one afterwards.
Health and safety on the day
Copiers are heavy and top-heavy, so keep staff out of the way while machines are being moved. Clear corridors of bins, boxes and trailing cables, and prop or hold fire doors only while the crew are passing through, closing them again afterwards. If the building has a permit system for using the goods lift or loading bay, have the permit ready. Make sure the crew know about any areas with restricted access, sensitive equipment or fragile floor finishes. A two-minute walk of the route with the crew lead before work starts usually prevents damage to walls, door frames and the machines themselves.
Combining with a wider clearance
If copiers are going because of an office move, refit or closure, think about what else is leaving at the same time. Computers, monitors, phones, servers, cabling and old UPS units can all go in the same visit, with data-bearing devices handled the same way as copier drives. One coordinated clearance with itemised paperwork is usually cheaper and simpler to record than several separate collections, and it avoids old equipment piling up in a meeting room for weeks.
Questions people also ask
Do I need to be present when the copier is collected?
Someone from your organisation should be on site to give access, confirm which machines are going and sign the waste transfer note. It does not need to be a senior manager, but it should be someone who knows the building and can make decisions if a machine turns out to be leased or a route is blocked.
Should I leave the toner in the copier?
Leaving installed cartridges in place is fine and reduces mess. Spare unopened cartridges are better bagged separately, as they can often be remanufactured or reused. Remove waste toner bottles carefully or leave them sealed in the machine, because they spill fine powder if knocked over.
Can copiers be removed outside office hours?
Yes, evening and weekend removals can be arranged, and some buildings require them for heavy items or lift bookings. They may cost more because of crew scheduling. Tell us any building rules, such as loading bay times or lift protection requirements, when you ask for a quote.
Written and checked by the Photocopier and Printer Disposal team. Read our editorial policy.
More guides
How Much Does Photocopier Disposal Cost in the UK?
In the UK, collecting a desktop printer or A4 multifunction device costs from £20, while removing a floor-standing A3 copier typically costs…
How to Wipe a Photocopier Hard Drive Before Disposal
Most modern multifunction copiers contain a hard drive or solid-state drive that can hold copies of scanned, printed and faxed documents, address…
Photocopier and Printer Disposal Rules in the UK
Photocopiers and printers are electrical equipment under the WEEE Regulations 2013, so they must be treated at an authorised facility, not…
End of Lease Photocopier: What Happens to the Old Machine?
At the end of a photocopier lease, the machine usually still belongs to the finance company. Your options are typically to return it, extend the…
Printers, Copiers and GDPR: Protecting Data When You Dispose
Many office copiers and multifunction printers store copies of scanned, printed and faxed documents on internal hard drives or memory, plus address…
Toner and Ink Cartridge Recycling for Offices: What to Do
Offices should recycle used toner cartridges, ink cartridges, waste toner bottles and imaging drums rather than putting them in general waste. Many…
Get a free photocopier and printer disposal quote
Tell us what you need and we'll come back with a clear price.
Request a quote